- $
Recommended news
- How to maintain Chongqing micro cultivator when it is parked for a long time
- When using micro cultivator, it should be used according to its performance and technical indexes
- "Three senses" identification method of micro cultivator accessories
- Selection criteria and suggestions of knife set of Chongqing micro cultivator
- Defect discrimination and cleaning method of micro cultivator accessories
Your location：Home > Information dynamic
> Industry dynamics
How to avoid damage of micro cultivator due to operation problems
Source:097wy.com Release time:2021/11/13 11:13:27
The micro cultivator can play different operation power by replacing different operation parts on the general frame. If we have a micro cultivator in our hands, we can realize busy farming operation with various functions. The operator of the micro tiller must be trained or familiar with the manual of the machine, and the operator who is not familiar with the operation method of the machine is prohibited.
1. The operator of the micro tiller must be trained or familiar with the manual of the machine, and the operator who is not familiar with the operation method of the machine is prohibited.
2. The operator of the micro tiller shall pay special attention to the safety warning signs on the machine, carefully read the contents of the signs and indicate other operators.
3. The operator of the micro cultivator shall pay attention to avoid being wound by moving parts to cause damage. Check whether all exposed rotating parts have been well protected.
4. The micro cultivator operators shall not work tired to avoid accidents.
5. Before each operation, it is necessary to check whether the smooth oil of the proposed machine and transmission box is sufficient.
6. Before use, it is necessary to check whether the components, transmission box and bolts of the proposed machine are loose and withered.
7. It is useful to check whether the operating parts (bits) can be activated.
8. When installing the plough knife, it must be recognized that the left and right are symmetrical and the working edge faces forward, otherwise it cannot be used normally.
9. It is suggested to check whether the concentrator can be in the separate orientation and whether the gear lever can be in the neutral orientation before starting the engine.
10. In order to ensure the normal operation of the proposed engine and prolong its service life, it is recommended that the proposed engine must be operated with no load. It can be operated 5 to 10 minutes before the hot vehicle. Do not operate with high speed and heavy load within 1 to 2 hours before the preliminary operation. If the engine runs too fast, the fuel supply or the air inlet shall be blocked quickly to stop the engine immediately.
11. The height of the resistance bar shall be adjusted at any time according to the operation conditions, and the degree and orientation of the fuselage shall be adhered to, so as to prevent the suggested machine from being damaged due to excessive skew, resulting in smoothness and insecurity of the suggested machine.
12. Avoid touching all kinds of rotating tools during operation, avoid stabbing, and stay away from the high-temperature area of the exhaust pipe. Be careful of scalding.
13. When changing tools, cleaning weeds and checking and repairing, it must be stopped before the suggested machine is interrupted.
14. It is forbidden to improve the operation speed of the machine in any way.
15. It is suggested that the rotating speed, power and other parts of the machine have been adjusted normally on the test bench, and it is forbidden to adjust at will.
16. The machine has no lighting device, and it is forbidden to work at night.
17. The micro cultivator shall drive at a low speed when working near corners, ditches, holes and canals in the field.
18. When adding fuel, stop the machine and avoid the war species.
19. When working in the slope area, pay attention to the balance of the machine. You can work along the slope direction, and the slope should be less than 25 degrees.
20. During machine operation, it is forbidden to approach or contact rotating parts to avoid accidents.
1. The operator of the micro tiller must be trained or familiar with the manual of the machine, and the operator who is not familiar with the operation method of the machine is prohibited.
2. The operator of the micro tiller shall pay special attention to the safety warning signs on the machine, carefully read the contents of the signs and indicate other operators.
3. The operator of the micro cultivator shall pay attention to avoid being wound by moving parts to cause damage. Check whether all exposed rotating parts have been well protected.
4. The micro cultivator operators shall not work tired to avoid accidents.
5. Before each operation, it is necessary to check whether the smooth oil of the proposed machine and transmission box is sufficient.
6. Before use, it is necessary to check whether the components, transmission box and bolts of the proposed machine are loose and withered.
7. It is useful to check whether the operating parts (bits) can be activated.
8. When installing the plough knife, it must be recognized that the left and right are symmetrical and the working edge faces forward, otherwise it cannot be used normally.
9. It is suggested to check whether the concentrator can be in the separate orientation and whether the gear lever can be in the neutral orientation before starting the engine.
10. In order to ensure the normal operation of the proposed engine and prolong its service life, it is recommended that the proposed engine must be operated with no load. It can be operated 5 to 10 minutes before the hot vehicle. Do not operate with high speed and heavy load within 1 to 2 hours before the preliminary operation. If the engine runs too fast, the fuel supply or the air inlet shall be blocked quickly to stop the engine immediately.
11. The height of the resistance bar shall be adjusted at any time according to the operation conditions, and the degree and orientation of the fuselage shall be adhered to, so as to prevent the suggested machine from being damaged due to excessive skew, resulting in smoothness and insecurity of the suggested machine.
12. Avoid touching all kinds of rotating tools during operation, avoid stabbing, and stay away from the high-temperature area of the exhaust pipe. Be careful of scalding.
13. When changing tools, cleaning weeds and checking and repairing, it must be stopped before the suggested machine is interrupted.
14. It is forbidden to improve the operation speed of the machine in any way.
15. It is suggested that the rotating speed, power and other parts of the machine have been adjusted normally on the test bench, and it is forbidden to adjust at will.
16. The machine has no lighting device, and it is forbidden to work at night.
17. The micro cultivator shall drive at a low speed when working near corners, ditches, holes and canals in the field.
18. When adding fuel, stop the machine and avoid the war species.
19. When working in the slope area, pay attention to the balance of the machine. You can work along the slope direction, and the slope should be less than 25 degrees.
20. During machine operation, it is forbidden to approach or contact rotating parts to avoid accidents.
